Windows 10 is known for its variety of advanced features and improvements. But like other Windows operating system, this sometimes become a big headache for its users. There are many Windows 10 update errors and other issues that irritate the users time to time.

And recently Windows 10 users are found reporting their Windows 10 get stuck at scanning and repairing drive. This is a big headache for the Windows 10 users as the process stuck for minutes or even hours.

Don't Miss The BEST TOOL to Fix Windows Errors  

However some users have reported that every time when they power on the PC they get the error message and was unable to do anything.  

Even the Chkdsk scanning and repairing the hard drive look like never completed and at last stop at different percent number.

Well, if you are the one struggling with Windows 10 scanning and repairing drive stuck issue, then Relax!

As here in this article I am going to describe the possible working solution to fix scanning and repairing drive stuck issue in Windows 10.

But before moving further here know why you are getting the issue.


Why Windows Is Scanning & Repairing Drive On Booting?


Well, there are many reasons behind this. If the Windows system did not turn off properly without warning then the reason could be a power failure, forced shutdown, bad sector on the hard drive, outdated drivers, or due to virus infection and others.  And as you start the system next time, the error message possible appears.

While Windows is running, the hard disk and RAM are writing and reading data. And the unexpected system shutdown can causes data loss stored in the RAM, and can even cause hard disk damage.

And as a result, when the system is booted next time, Windows scan the drive automatically and try repairing the issue that might occur due to sudden system shout down.

Please Note: It is recommended avoid the force turn off of the system, while it is being used. This might cause you data loss situation.


How to Fix Windows 10 Scanning and Repairing Drive?


The scanning and repairing process might take a long time or get stuck there. Well, if you don’t require using Windows immediately, then wait till the process is done.

However, if you don’t want to wait then try bypassing the auto-scanning and utilize other methods to scan and repair drive manually.


Step 1: Enter Windows 10 or the Safe Mode


  1. Ways to Enter Windows 10

To enter desktop, hold down the power button for few seconds and restart the system. And repeat the process few times till you get the message “press any key to bypass the chkdsk” on the screen.

After that hit any key to skip the scanning and enter your password to log in Windows 10.

  1. Ways to Enter the Safe Mode

However, if this won’t help you then press and hold the power button continuously to shut down. Repeat this at least 3 times, till you see the Recovery screen. And click on See advanced repair option button > Troubleshoot >Advanced options >Windows Startup Settings >Restart. Hit F4/F5 to Enter Safe Mode (with Networking).

After entering the desktop, check each disk on the computer to check if the disk error still appears. Well, if not then disable the irritating “scanning and repairing drive” ” CHKDSK on booting.

You May Also Like: 


Step 2: Verify the Disk Errors in Windows 10


To fix the issue verify the disk in Windows 10 and repairs the errors.

  • Press Win + E key to launch File Explorer > right click on the Local disk (C:, D:, E:, etc.) > choose Properties.
  • Then select Tools tab > click on Check.

  • After that to start the scanning click Scan drive.
  • As the process is finished, Error Checking box might pops up. Here click Scan and repair drive > follow the on-screen instructions to repair errors.

  • If no any errors were found, then just close the box.

But assure that the drive is scanned properly and errors are repaired as well. However if still you are getting the scanning and repairing  drive loop, then change the registry and disable the CHKDSK on booting.

Helpful Article: 5 Ways to Fix Windows 10 100% Disk Usage in Task Manager


Step 3: Disable Scanning and Repairing Drive on Booting


Well, it is found that disabling the scanning and repairing the drive on booting helped many users to fix the issue. So here it is recommended to try this once.

Follow the process to do so:

  • Press Win + R key to launch Run > type regedit > Enter.
  • Now follow the below given command and expand the entries and then move to BootExecute on the right column.
  • HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager
  • Next double click BootExecute > the default value is autocheck autochk * >  replace it with autocheck autochk /k:C * and click OK.

Please Note: It is recommended to backup the registry entries first in case any serious system, issues occurs.

Also Read: 7 Tricks to Fix Windows 10 Automatic Repair Failed Loop


Step 4: Check for Outdated Drivers


As I said above many users have reported they are facing the issue due to the outdated drivers.

So, it is recommended to update the drivers, check for the compatible drivers in the manufacturer website or else in the Microsoft Official website.

And try updating the outdated drivers or else you can also install the latest one compatible with your system.

After that check Windows 10 scanning and repairing drive stuck issue is solved or not.

Well, if you are not technically savvy and don’t know the exact process to update the drivers then update them easily just by clicking once.


Step 5: Utilize a System Restore Point


If after following the above given steps your PC still got stuck at scanning and repairing drive after power failure or some important system’s changes. Then it is recommended to perform a System Restore Point.

Follow the steps to do so:

  1. First open Control Panel > select Recovery.
  2. Then click on the Open System Restore link > click Next.
  3. After that select the previously created Restore Point when the “Scanning and repairing drive” error occurred.
  4. Lastly, click Next > wait while the restore process is being executed.

Hope after following the above given solutions you are able to get rid of the scanning and repairing drive stuck issue in Windows 10 booting and runs your Windows 10 Pc without any issue.

But if not then it is recommended to make use of the Windows Repair Tool, this is the best solution to repair various Windows 10 issues easily.


Check your Windows PC/Laptop Health


Make use of the professional recommended Windows Repair tool, this is the best tool to scan, detect and repair various Windows related issues such as corruption, damages of the Windows system files, malware/viruses, protect you from file loss, hardware issues and many more. Quickly fix various issues like BSOD, DLL error, Registry issues, drivers issues, games relates issues, application error and many others. Apart from that, it helps you to optimize your Windows PC performances and prevents others issues automatically with this software.




Well, I tried my best to provide the best solutions to fix scanning and repairing drive stuck issue in Windows 10

Try the given solutions one by one and check whether the irritating error is fixed or not.

Apart from that, scan your system for the virus/malware at the regular interval of time and update Windows 10 OS with the latest update to make the system perform better and healthy.

Additionally, if you find the article helpful or have any query, comment, questions or suggestions related, then please feel free to share it with us in the comment section below or you can also go to our Fix Windows Errors Ask Question Page.

Good Luck!!!

5 Methods to Fix Scanning and Repairing Drive Stuck Issue for Windows 10
Article Name
5 Methods to Fix Scanning and Repairing Drive Stuck Issue for Windows 10
Utilize the given working solutions to fix Windows 10 scanning and repairing drive stuck issue and run your Windows 10 system properly
Publisher Name
Fix Windows Errors
Publisher Logo

5 Methods to Fix Scanning and Repairing Drive Stuck Issue for Windows 10